Schlagwort-Archiv: Elevator Manufacturers

Elevator Manufacturers: Improvement of Elevator Hardware

Elevator energy has long been neglected. However, these machines account for 3-7% of building energy consumption, so while elevators may not be your biggest energy source, they can save a lot of money and energy. How to improve elevator efficiency to a new level? Elevator Manufacturers Fuji offers some methods.

Intelligent tracking strategy

The first step is to understand how much energy each machine uses to increase elevator efficiency. The sub-table includes the installation of a data logging device throughout the elevator group to measure the current and voltage in the input line.

Where can I find waste?

To determine the most cost-effective improvements, the next step is to check which components are responsible for the most energy.

Based on the above two points, the hardware improvements you can make include:

Motor: Replacing an old-fashioned DC motor with an AC motor can save 50% of energy.

Lighting: Replace fluorescent, incandescent, and halogen lamps with efficient, low-calorie LED lighting and replace buttons on the cab panel, overhead fixtures, and floor indicators.

Door: Not used when using the door drive motor to enter standby mode, then resume when needed.

Starter: Replace the old starter with a new starter to increase energy efficiency while preventing low quality power supplies that can cause voltage shortages.

Landing system: Replace the old landing system with magnets or tapes with a new landing system that stops the cab faster and does not run the motor for long periods of time.

Lights and fans: These lights and fans can be turned off, if the elevator is stationary, parked after a predetermined time.

Finally, regular maintenance is the key to keeping costs low. This is also to maintain expensive maintenance, but the maintenance of the elevator is a must, you should pay attention to it, good maintenance can improve the efficiency of the elevator and keep the elevator in good condition.

Elevator Manufacturers Fuji Explains New Elevator Technology

The elevator has been developed for a long time and the development of elevator technology will not stop. Elevator Manufacturers(fujihd) will continue to develop new elevator technologies. The development of elevator technology is mainly concentrated in the following aspects:

Super high speed elevator:

In the 21st century, with the further intensification of the contradiction between population and available land area, the multi-functional and functional high-rise tower buildings will be booming, and ultra-high-speed elevators will continue to be the research direction. In addition to traction elevators, linear motor-driven elevators will have a lot of room for development. How to ensure the safety, comfort and convenience of the elevator has become the research direction in the future.

Elevator intelligent control system:

Elevator control system will be closely integrated with network technology, which connects separated elevators in use with network, collects and monitors their operation situation in real time, integrates them into maintenance management system, repairs the faults quickly and effectively, and conducts online transactions through elevator website, which can be achieved. Now elevator procurement, configuration, bidding, etc., can also apply for on-line elevator inspection work.

Gearless elevator:

Gearless machinery, ropes and counterweights replace traditional hydraulic equipment. The main rails are mounted on either side of the elevator car and the other set of weight rails are mounted on the side or rear of the elevator car. The AC permanent magnet gearless motor is mounted on the top beam and does not require a machine room, thus reducing construction costs. Gearless elevators do not require jack holes, which eliminates drilling costs and reduces the risk of oil contamination.

How to Make Your Family Safely Take the Elevator

Elevators have changed the lives of millions of people around the world. The role of these devices in improving employee mobility and independence cannot be ignored. This article aims to raise public awareness of the safety of elevators, escalators and moving walkways. Elevator Manufacturers Fuji summed up the safety knowledge of elevators and escalators.

For children

Move wide, bright, and bright steps. Thick rubber handle. You can see your side. Mobile playground? No, it is an escalator. Children can play almost any game, and escalators are no exception. Although you know that escalators are not toys, many children don’t know. Children should not place their hands or feet between the moving door and the side door of the adjacent door. Children should not try to put their hands or feet on the road.

Adult

Hold the child and pet firmly, stay away from the door, keep the clothes and remove them from the opening. If you need to open the door or ask someone to press a button, press and hold the “door open” button, but do not press or hold the door in any other way. turn on. What should not be done when the elevator is parked between floors:

Do not force the door open

Don’t try to leave the elevator. The elevator hatches are designed for professionals and they will help out of the elevator car.

Use the warning button and wait for help.

If the call is available, follow the instructions to summon help.

keep patient. There is plenty of air and the interior of the elevator is designed for passenger safety.

Following these simple guidelines will make driving more comfortable and safe.

Why Elevator Manufacturers Value Modular Elevators

In addition to the most innovative and advanced elevators on the market, modular elevators are also your best choice. The modular elevator is a new type of elevator that Elevator Manufacturers have spent a long time designing. Modular elevators have many features. So, when do you need to choose a modular elevator? Fuji can give you the answer.

Modular elevators are pre-designed, although many other elevators are not pre-designed, but modular elevators are pre-designed. This gives the buyer many benefits. This is because it saves a lot of money for pre-designed things, which will ultimately save everyone’s money in the long run. It also saves a lot of time through pre-designed modular elevators, which is valuable. The modular elevator car is made of the finest steel. This makes them extremely durable and safe.

Installing a acceptable elevator can be cumbersome. Modular elevators are accepted bartering elevators army on prefabricated structural animate shafts. The anchored animate brace anatomy consists absolutely of elevator cars, rails, ascendancy units and centralized drive systems. It is coated with abstracts to accommodated architectural requirements. The modular elevator barter is again transported to the website and aerial by the crane and installed in the elevator pit. Once installed, it functions like a athletic elevator and provides the account in the aforementioned way.

Modular elevators can be installed in ample buildings, accessible spaces and clandestine homes, and accessible accession locations are not restricted. The versatility of modular elevators allows them to be acclimated about anywhere. Acceptable elevator architecture takes time and money. Regardless of the blazon of elevator used, anniversary elevator requires maintenance, but modular elevators crave actual little maintenance.

Elevator Manufacturers Fuji: Common Problems with Elevators

From old operating systems to worn pulleys, there are many reasons why elevators can fail. Elevator Manufacturers Fuji has studied some of the most common elevator problems and provided solutions to prevent elevator downtime.

The amount of the elevator arrangement is the elevator apparatus room. It includes elevator absorption machines, motor architect sets or solid accompaniment ability supplies, as able-bodied as ascendancy equipment. Ascendancy accessories is an important allotment of the absolute operating mechanism, which accelerates, decelerates and leveles anniversary floor. Most of the circadian aliment is agitated out in the apparatus room. This includes accepted aliment of motors, generators, switches, contacts, brakes and controls. Here are some accepted questions:

1. Problem: beat pulley

Pulleys with beat pulleys could could cause added abrasion on the ropes, accretion the abrasion of the pulleys. This creates a besmirched bend for the key components. The position of the caster can be afflicted or replaced, so be abiding to analysis the canal contour to verify the fit amid the braiding and the pulley.

2. Problem: Motor drive misalignment

When the motor is aligned, the motor is affiliated to addition accessory and shaft alignment is critical. If not appropriately aligned, the motor bearings will activate to wear. Misalignment of the shaft can be detected application avant-garde laser barometer accessories or artlessly application adjudicator chords.

3. Bearing noise or bearing failure

Spherical roller bearing bearing failures cause more than half of the motor failure. Noise bearings are often attributed to vibrations within the motor. We can use an inductive absorber to sink current and protect the system from potential faults. Also, ensure that all grounding is protected and connected to minimize failures caused by electrical noise on the ground.

Elevator Manufacturers: Characteristics of Hydraulic Elevators

Hydraulic elevators and rope elevators are the two main types of elevators used today. Today, Elevator Manufacturers Fuji takes you through the advantages and disadvantages of hydraulic elevators.

hotel elevators

The hydraulic lift includes a piston and cylinder arrangement that is coupled to the hydraulic system. The tank is filled with hydraulic oil (oil or other highly viscous liquid) and connected to the cylinder through a valve.

When the control system signals the elevator to move up, the pump (controlled by the motor) pushes hydraulic fluid into the cylinder. At this point the valve closes and there is nowhere to enter the cylinder. When it does so, it forces the piston to move up, pushing the elevator up. When the elevator car approaches the signal floor, a signal is sent to the motor to shut down, thereby stopping liquid flow and subsequent movement of the piston and elevator.

The advantages of hydraulic elevators include:

No need for an elevated machine room

Elevator shaft size optimization

The load is distributed on the load-bearing wall without the need for overhead structures.

The equipment room can be positioned remotely.

Installation costs are typically lower than the cost of installation of conventional traction rope systems.

Disadvantages of hydraulic elevators include:

Pump unit and control system require machine room

Limited speed and performance

High noise level compared to other systems

Heating the smell of oil

Environmental problems caused by the heavy use of oil

Poor ride quality compared to other systems

Elevator Manufacturers and Elevator Preventive Maintenance

Maintaining your elevator, whether in a corporate office building or an apartment building, is critical to extending the life of your equipment and ensuring passenger safety. Regular maintenance is the responsibility of the property manager or owner of the local city or town. Employ the Elevator Manufacturers to regularly repair the elevator, but before that, please pay attention to the following matters.

Make sure the elevator room meets the specifications. The elevator itself not only needs to be in good working conditions, but also in the machine room. Partial maintenance means ensuring that the elevator car is automatically closed and locked so that no one can enter without authorization, the room has adequate lighting, and the room is not used for storage, which is a fire hazard.

Workers typically perform preventive maintenance, such as refueling and lubricating moving parts, replacing worn parts, and adjusting equipment for optimum performance. Unlike most elevator installers, personnel specializing in elevator maintenance typically serve multiple identical elevators over multiple time periods. They also troubleshoot and may require urgent repairs.

The easiest way to monitor the quality of service is to track the number of failures. Track the number of failures per elevator and the cause of each failure. At the same time, pay attention to the quality of the ride. The ride feels up and down the elevator. Finally, check if the automatic door opens and closes smoothly.

Elevator Manufacturers Takes You to Distinguish the Elevator

Elevator manufacturers can offer a variety of different drive elevators. Now, Elevator Manufacturers Fuji takes you through the difference between hydraulic and traction elevators.

Hydraulic elevator

The hydraulic lift pumps hydraulic oil to the cylinder/plunger assembly, causing the piston to move vertically, moving the lift up and down. Conventional cylinder/plunger assemblies are located in the wellbore directly below the elevator, and many years ago these components were installed with little or no protection for underground components. If the parts on the lower surface cannot be inspected, the damage to the hydraulic cylinder that eventually causes the hydraulic oil to leak will be ignored. When this happens, it usually causes soil and groundwater pollution.

Any maintenance contract does not include maintenance of the elevator. The cost of the cylinder/plunger assembly (including the required contaminant repair) can be as low as $30,000 and in some cases can exceed $100,000.

Keep in mind that hydraulic elevators need to be provided in a controlled environment where additional heating is required, and in some cases air conditioning is required. Remote pipelines operating underground are another potential problem for temperature control and potential leaks.

Traction elevator

The traction lift is driven by a machine that includes a steel sling that rides on a drive pulley and is typically attached to a counterweight assembly and a car crosshead. For overhead traction elevators, you need to provide a top floor structure that surrounds the elevator equipment and supports the elevator load. MRL elevator equipment is usually mounted on rails and transfers loads to elevator pits. MRL elevator designs typically have lower overhead requirements and allow designers to provide the desired smoother roof line appearance.

Elevator Manufacturers Call for Attention to Elevator Maintenance

More and more buildings are equipped with elevators, which is a very convenient transportation device. Except for elevator technicians, few people think of the mechanical structure of the elevator until it fails. How to keep the elevator in top condition? The Elevator Manufacturers can give you some advice.

Maintenance of the elevator is a must, and approved aliment of the elevator can extend the activity of the elevator. Routine aliment of the elevator have to be abiding with the architect or a acclaimed company. Please chase the adjustment instructions beneath to ensure that the elevator is operating effectively:

Keep the temperature about the elevator at a nominal level. The accepted operating temperature is 15 to 32 degrees Celsius. Check the elevator for automated or concrete accident every day. Always accrue the breadth about the elevator apple-pie and abolish any bits that could baffle with the elevator’s operation. In the continued run, even a baby bulk of dust and dust will accumulate.

Maintenance is mainly disconnected into the afterward types:

Routine maintenance: Includes all user interface aspects of the elevator, such as alarm buttons, displays, elevator leveling, walkie-talkie, ARD. Lights, aperture operations, etc.

Preventive maintenance: Some locations of the elevator, such as machines, ropes, bearings, car guides, adviser rails, etc., accomplish antitoxin aliment at the defined frequency.

Troubleshooting: Adjustment or alter specific locations to restart the elevator in the accident of a failure.

Elevator Manufacturers Keeps the Elevator Running for a Long Time

Passenger Elevator refers to elevator that only carry people between floors. These elevators are usually very heavy in the range of 500-3000 kilograms. These two types – electric and hydraulic, can be moved to the eight level. These can reach speeds of about 200-500ft / min. In buildings over ten storeys, a gearless elevator can also be operated at a similar speed, while elevators above ten storeys can travel at speeds of 2000 ft / min. Passenger elevators provided by these Elevator Manufacturers for small buildings, such as domestic or large buildings. These residential elevators operate slowly and have poor carrying capacity, but passenger elevators installed in large buildings have higher carrying capacity and are faster between floors.

Choose the right passenger lift from elevator manufacturers:

Speed: speed is not just speed up, but speed and gate are also important

Quality: the quality of the material elevator is based on

Safety and backup function: elevator movement during electric cutting.

Elevator instructions and load capacity

Maintenance costs and availability of services are needed

The elevators are well equipped and built on the most advanced technology. These elevators are very helpful for physically challenged people and for older people, and there is plenty of room for wheelchairs, just in case one person will move. The security functions are interlocked door locking systems, manual door holders, telephones, security cameras, air conditioners, etc.. These elevators have lower waiting times and downtime. If these elevators, the minimum braking drop, the phone is some guarantee. Passenger elevators require less maintenance than other elevators.

villa elevator

When these elevators are well monitored, they can operate effectively over a long period of time. Passenger elevators are environmentally friendly and consume much less power. Other safety features of these elevators include fireman’s switch, emergency stop button, pit switch, interlock button, overspeed button, motor overload protection, etc.. Some normal functions are digital cab position indicator, comprehensive collective control, automatic / manual operation, door opening buzzer, emergency alarm bell, cab ventilation, and so on. Elevator manufacturers produce and deliver passenger elevators, fully install all safety features.