Schlagwort-Archiv: BMW ICOM A3 Pro

How to Reset a Compass on a Toyota FJ Cruiser

There are two calibration procedures that you can perform for the compass in your FJ Cruiser. The deviation calibration must be performed anytime your vehicle has been permanently moved to a different geographical location. The second calibration is the circling calibration that calibrates the compass to magnetic north.VXDIAG VCX NANO You may have to perform both of these procedures for the compass to work accurately, so be sure you perform these procedures in an area where you can drive in a complete circle when prompted.
BMW ICOM A3 Pro VXDIAG VCX NANO MVP Key Programmer BMW ICOM A3 Pro VXDIAG VCX NANO MVP Key Programmer BMW ICOM A3 Pro VXDIAG VCX NANO MVP Key Programmer BMW ICOM A3 Pro VXDIAG VCX NANO MVP Key Programmer BMW ICOM A3 Pro VXDIAG VCX NANO MVP Key Programmer

Deviation Calibration Procedure

Turn on the ignition and press the “Set” button on the outside temperature display until the zone number is displayed in the outside temperature display.

Refer to the calibration map in your owners manual.MVP Key Programmer Then press the “E/M” button repeatedly on your temperature display until the zone number matches the zone where you are located on the map in your owners manual.

Push and hold the “Set” button until the temperature display reverts back to displaying temperature.
BMW ICOM A3 Pro VXDIAG VCX NANO MVP Key Programmer BMW ICOM A3 Pro VXDIAG VCX NANO MVP Key Programmer BMW ICOM A3 Pro VXDIAG VCX NANO MVP Key Programmer BMW ICOM A3 Pro VXDIAG VCX NANO MVP Key Programmer BMW ICOM A3 Pro VXDIAG VCX NANO MVP Key Programmer

Circling Calibration Procedure

Turn on the ignition and push the “Set” button on your temperature display until the zone number is displayed in the temperature display

Press the “Set” button again so the display will revert to displaying two dashes “–”

Drive in a circle at about five miles per hour.BMW ICOM A3 Pro Your temperature display will revert back to displaying outside temperature when the calibration is complete. If “Er” is displayed, the calibration did not complete. You will have to repeat the circling calibration procedure again.

How to Install a TS Performance Chip

The TS performance chip is an aftermarket computer chip specially designed to replace the stock PCM, or powertrain control module, chip in Ford Powerstroke Diesel engines.Renault CAN Clip The TS performance chip increases horsepower and vehicle torque when necessary, all while providing better fuel economy and cleaner vehicle emissions. You can replace the stock PCM chip in your Ford truck with a TS performance chip yourself with a few tools and about thirty minutes.
Digiprog III Renault CAN Clip BMW ICOM A3 Pro Digiprog III Renault CAN Clip BMW ICOM A3 Pro Digiprog III Renault CAN Clip BMW ICOM A3 Pro Digiprog III Renault CAN Clip BMW ICOM A3 Pro Digiprog III Renault CAN Clip BMW ICOM A3 Pro

Park your truck and switch off the engine. Remove the key from the ignition.

Raise the hood and disconnect the negative battery terminal from each of the two batteries using a ratchet. One battery is located on the left front side of the vehicle and one on the right front side of the vehicle.

Look beneath the driver side dash and locate the emergency brake bracket at the top of the emergency brake pedal. Remove the three bolts securing the bracket in place using a ratchet. Remove the bracket.

Locate the wiring harness in the engine compartment that connects the PCM to the vehicle ECU. The wiring harness is on the driver’s side, near the front fender.BMW ICOM A3 Pro Lift the clip on the wiring harness and disconnect it.

Remove the two bolts securing the computer chip metal casing behind the emergency brake pedal, using a ratchet. The computer chip casing is a metal case approximately three inches by three inches.
Digiprog III Renault CAN Clip BMW ICOM A3 Pro Digiprog III Renault CAN Clip BMW ICOM A3 Pro Digiprog III Renault CAN Clip BMW ICOM A3 Pro Digiprog III Renault CAN Clip BMW ICOM A3 Pro Digiprog III Renault CAN Clip BMW ICOM A3 Pro

Remove the third and fourth bolt securing the top and bottom of the computer chip casing below the dash, if your vehicle has a manual transmission. Skip this step if your vehicle is automatic; it does not have these extra bolts.

Remove the computer chip metal casing from the vehicle.

Peel back the tape holding the old computer chip in the metal casing and slide the old chip out of the casing.Digiprog III Note that the chip connects to an electrical harness within the casing. Unplug the electrical connector once you remove the chip and set the old chip aside.

Connect the TS performance chip to the electrical harness and slide the chip into the metal casing.
Digiprog III Renault CAN Clip BMW ICOM A3 Pro Digiprog III Renault CAN Clip BMW ICOM A3 Pro Digiprog III Renault CAN Clip BMW ICOM A3 Pro Digiprog III Renault CAN Clip BMW ICOM A3 Pro Digiprog III Renault CAN Clip BMW ICOM A3 Pro

Cover the opening on the metal casing with duct tape to protect the computer chip.

Reinstall the computer chip casing and emergency brake bracket using the bolts you removed. Tighten until secure.

Reconnect the ECU electrical connector on the driver’s side, under the hood. Reconnect the negative battery terminals and start the truck.

How to Reset a Computer in a 2002 GMC Envoy

The 2002 GMC Envoy has an electronically controlled engine that requires a computer to function properly. The computer, a Power train Control Module or PCM, monitors the engine’s sensors and makes adjustments, as necessary, to enhance engine performance.BMW ICOM A3 Pro If the PCM is not operating correctly, the engine may run rough and gas mileage may be lower than normal. The PCM may need to be reset when an engine sensor or electronic part is replaced. The procedure to reset the PCM is easy, even for the novice mechanic.
BMW ICOM A3 Pro MVP Key Programmer Renault CAN Clip BMW ICOM A3 Pro MVP Key Programmer Renault CAN Clip BMW ICOM A3 Pro MVP Key Programmer Renault CAN Clip BMW ICOM A3 Pro MVP Key Programmer Renault CAN Clip BMW ICOM A3 Pro MVP Key Programmer Renault CAN Clip

Park and turn off the vehicle’s ignition. Open and secure the hood. Disconnect the negative battery cable with an adjustable wrench.

Turn on the vehicle’s headlight switch inside the vehicle’s passenger compartment.MVP Key Programmer The lights will not come on with the battery disconnected, but any remaining power will drain. Wait five minutes and turn off the headlight switch.
BMW ICOM A3 Pro MVP Key Programmer Renault CAN Clip BMW ICOM A3 Pro MVP Key Programmer Renault CAN Clip BMW ICOM A3 Pro MVP Key Programmer Renault CAN Clip BMW ICOM A3 Pro MVP Key Programmer Renault CAN Clip BMW ICOM A3 Pro MVP Key Programmer Renault CAN Clip

Connect the negative battery cable with an adjustable wrench.

Drive the vehicle for at least 30 minutes to allow the computer time to reset.

Tips & Warnings

Read the vehicle’s owner’s manual to learn how to reset the clock and radio presets,Renault CAN Clip if necessary.