Alle Artikel von posuiman

Selection Considertions of the Working Speed of Ultrafine Mill

The selection of the working speed of Ultrafine Mill is very important since it influences the production efficiency of Ultrafine Mill. Here will explain the conditions should be taken into consideration in the selection of the working speed of ball mill: (1) The surface shape of scale board: The surface shape with convex edge can reduce the relative sliding of crushing media. For this reason, if the workers increase the hoisting height, the working speed of the ball mill should be lower than that using smooth scale board.

Mineral hardness and Ultrafine Mill fineness: When roughly grinding the hard and large pieces of rock, you should use larger crushing media and higher working speed, which will be helpful to increase the impacting effect on the materials. On the contrary, you’d better use smaller crushing media and lower working speed in order to strengthen the crushing and grinding effects and reduce energy consumption. Grinding methods: As for wet type grinding, due to the lubricating effect of water, there will be obvious relative sliding between the crushing media and the scale board.

Therefore, on the similar condition, the working speed of wet Ultrafine Mill should be improved by 5% higher than that of dry type ball mill. Filling ratio of crushing media: The lower the filling ratio is, the higher the relative sliding will be. For this reason, the working speed should be higher. Through abundant experiment and rich experienced information, it was believed that improving the working speed of Ultrafine Mill is beneficial from the perspective of output. The domestic experiential data shows that when the working speed is increased, the productivity can be greatly improved. But the life of scale board will be rapidly decreased and the power consumption will increase. Consequently, the working speed of the ball mill is often adjusted between 76% and 88%.

Ore Milling Equipment Flings to International Market

This year, the development of the foreign trade in our Ore Milling Equipment country will actively carry out the strategy of “going out”. Chen Deming, Minister of Commerce Department expressed on the working conference of national business the other day, that the government in our country will encourage some powerful enterprises to invest and merge and acquire and integrate resources in the global range and conduct research and development, production and marketing activities and cultivate famous brand in the international market and strengthen the support for the going out policy of the private companies.

Construction waste is mainly in the solid form and is mainly produced in the Ore Milling Equipment building process of the maintenance and removing process of the old buildings. Different structure types of building the waste generated in the various components of the content is different, but the basic composition of the material is consistent, mainly by soil and waste, swathes of the mortar and concrete, cut off the bricks and concrete produced pieces, metal, wood, bamboo adornment to decorate a waste, all kinds of packaging materials and other waste etc.

Among them, the use of abandoned buildings and Ore Milling Equipment thickness aggregate production can be used in the production of the corresponding intensity level of the concrete, mortar or preparation such as blocks, wall, floor tile and building materials products; Using waste brick production aggregate can be used in the production of renewable brick, blocks, wall, floor tile and building materials products, with realize construction waste reduction and recycling, saving natural resources, and protect the ecological environment advantage, and has high economic value. Among the engineering equipment that is needed in the disposal process of the construction waste, jaw crusher get popular acceptations and praises among the customers because of its low energy consumption and environmental protection.

The Crushing Manner of Ore Milling Equipment

The composition of the single rotor Ore Milling Equipment is relatively simple, and it is mainly composed by the machine rack, driving machine, rotor hammer and the impacting plate. Among them, the rack is made up of the upper rack and the lower rack, and they are connected by the bolt. The part that is on the axial lead of the rotor is called upper rack, on which there are installed the side door and the back door for examination and installation.

The part that is under the axial lead of the rotor is called lower rack, which is fixed on the ground with bolt in order to sustain the weight of the whole Ore Milling Equipment. All the parts that need to touch the rocks inside the rack are installed with changeable wear-resisting lining board. The Ore Milling Equipment mainly uses the impacting theory to realize the selective crushing to the materials, so that the granularity of the final products produced by the machine is good and the qualified rate is very high, so that it is often used for the final crushing in the roadbed and road surface which has higher requirement for the aggregates, and it is also used in the crushing and production process in such industries as building materials, chemistry and mining.

The Ore Milling Equipment mainly relies on the hammer with high rotary speed to impact the materials, and selectively crusher the weak part. The impacted materials will get huge kinetic energy, and after the mutual impact and friction of the impacting plate and the materials, the purpose of further crushing will be achieved and until the final qualified products are screened. With the constant development of the science and technology, the manufacturing technology and materials of the impact crusher will continuously update and change so that it will better satisfy the demands in the modern industry and building industry. As a professional and the best mining machinery manufacturer in China, Machinery is always ready to provide the superior dryer machine with the best quality and the most competitive price.

A Building Block to Infrastructure Construction

With the development of China’s infrastructure Construction Waste Crusher, the need for natural sand is gradually increasing; only natural sand can no longer meet the demand of construction. The sand making equipment appears very timely and then produces the artificial sand which perfectly substitutes the existence of natural sand.Our company researches and develops the new type cone sand maker which has a significant effect especially for the building sand. Due to the high quality and broad range of the fine sand material which produced by the sand making equipment, it is well-received by a variety of customers. The cone sand maker which is produced by us is outstanding with its unique design and thus distinguishes from other companies.

Ore Milling Equipment such as rock crusher is now used in construction field to crush large building wastes. On one hand, the disposed wastes are small in size which makes them easy to transport and place. Meanwhile, this practice reduces the cost onmanual work.Meanwhile, the technology which we used has been awarded a national patent certificate. Now, the experts from will explain the structural features of the cone sand maker and hope that can be helpful to our customers.

Combining with advanced technology and many years’ experience, we improve the technology level and manufactures world advanced high-performance sand making equipment. In the future, will make more progress and greatly contributes to the construction industry.